南京CadencePCB設計高級培訓班

第一天

1、高速PCB設計中的理論基礎

傳輸線理論、信號完整性（反射、串擾、過沖、地彈、振鈴等）、電磁兼容性和時序匹配等等。

2、SPECCTRAQuest設計流程

2.1 Pre-Placement

2.2 Board Setup Requirements for Extracting and Applying Topologies

2.3 Database Setup Advisor

—Cross-Section

—DC Nets

—DC Voltages

—Device Setup

—SI Models

—SI Audit

3、拓撲結構的抽取與仿真 Extracting and Simulating Topologies

3.1 Pre-Route Extraction Setup—Default Model Selection

3.2 Pre-Route Extraction Setup—Unrouted Interconnect

3.3 Pre-Route Template Extraction

3.4 SQ Signal Explorer Expert

3.5 Analysis Preferences

3.6 SigWave

3.7 Delay Measurements

第二天

4、確定和施加約束 Determining and Adding ConstraintsSolution

4.1 Solution SpaceAnalysis: Step 1 to 6

4.2 Parametric Sweeps

4.3 Constraints

Topology Template Constraints

Switch/Settle Constraints

Assigning the Prop Delay Constraints

Impedance Constraint

Relative Propagation Delay Constraint

Diff Pair Constraints

Max Parallel Constraint

Wiring Constraint

User-Defined Constraint

Signal Integrity Constraints

4.4 Usage of Constraints Defined in Topology Template

5、模板應用和基于約束的布局

Template Applications and Constraint-Driven Placement

5.1 Creating a Topology

5.2 Wiring the Topology

5.3 TLines and Trace Models

5.4 Coupled Traces

5.5 RLGC Matrix of Coupled Trace Models

5.6 Crosstalk Simulation in SQ Signal Explorer Expert

5.7 Simulating with Coupled-Trace Models

5.8 Sweep Simulation Results with Coupled-Trace Models

5.9 Extracting a Topology Using the Constraint Manager

5.10 Electrical Constraint Set

5.11 Applying Electrical CSet

5.12 Worksheet Analysis

5.13 Spacing and Physical Rule Sets

5.14 Electrical Rule Set

第三天

6、基于約束的布線 Constraint-Driven Routing

6.1 Manual Routing

6.2 Routing with the SPECCTRA Smart Route

6.3 Driving Constraints in Routing

7、布線后的DRC檢查和分析 Post-Route DRC and Analysis

7.1 Post-Route Analysis

7.2 SigNoise

7.3 Reflection Simulation

7.4 Reflection Waveform Analysis

7.5 Comprehensive Simulation

7.6 Crosstalk Simulation

7.7 Crosstalk Analysis

7.8 Simultaneous Switching Noise Simulation

7.9 SSN Waveform Analysis

7.10 System-Level Analysis

7.11 A Complete Design Link

7.12 Initialize Design Link

8、差分信號設計 Differential Pair Design Exploration

8.1 Types of Differential Pairs in SPECCTRAQuest

8.2 Create Differential Pair Using SPECCTRAQuest

8.3 Create Differential Pair Using Constraint Manager

8.4 Assigning Differential Pair Signal Models

8.5 Preference to Extract Unrouted Differential Pair Topology

8.6 Extracting Unrouted Differential Pair Topology

8.7 Custom Stimulus to Analyze Differential Pair Topology

8.8 Differential Pair Topology Analysis

8.9 Coupled Trace Model and Differential Pair Topology

8.10 Layout Cross-section Editor

8.11 Differential Pair Constraints

8.12 Differential Pair Constraints in the Constraint Manager

8.13 Differential Pair Analysis in the Constraint Manager

8.14 Post Route Extraction